Audi A3, S3/TT/VW Golf Inc GTI, R (1.8T/2.0 TFSI EA113)
In Stock:
This product is in stock & ready to be dispatched.
Limited Stock Available:
Stock is running low. Order soon to avoid missing out!
Almost Gone:
Stock is critically low! This product may sell out soon.
Incoming:
Product will be in stock soon.
Usually Ships In:
This product is out of stock and will usually ship in the timeframe displayed.
Sold Out:
This product is currently out of stock.
Request ETA
$104.95
Unit price /
Unavailable
Bidit helps you and Pro Speed Racing agree on a price. You set the price and Pro Speed Racing checks if they can accept your offer. You aren't competing with anyone else.
Save your engine from complete timing failure from dropped timing belt with this performance-designed IE/ARP Crankshaft Damper Bolt Upgrade.
UNRELIABLE STOCK CRANKSHAFT TIMING GEAR
The factory installed crank damper and timing belt drive gear interface is one of the highest failure issues with the VW & Audi 20V 1.8T and 12V 2.0T FSI engines. This timing interface does not have a safety factor from the factory and commonly leads to lost timing and complete engine failures. This issue is only increased on performance engines when combined with higher RPM. The factory bolts are frequently shipped loosely without thread protection. leading to erratic clamping loads and further resulting in engine failure rates.
RELIABLE PERFORMANCE DESIGNED REPLACEMENT BOLT
This IE designed and ARP manufactured Crank Damper Bolt addresses all the issues with under-spec factory bolt providing a strong, reliable, and quality upgrade solution. Manufactured from aerospace grade materials resulting in extremely consistent thread quality and strength. This timing increases clamping loads by over 10%, reliably ensuring a slip-free interface and protection against sheared timing gear keyways.
Using a 13/16†12 point drive and quality verified torque wrench, torque your new IE/ARP crank bolt to 78 FT-LB + 1/4 turn using red Loctite ®.
INSTALL NOTES:
The final 1/4 turn equates to a lot of torque, this requires a long bar to complete the turn, be prepared. Thoughrouly clean and inspect the threads in the crankshaft ensuring they are clean and free of debris before installing your bolt. This IE ARP bolt is reusable if for any reason you need to remove it, heat the bolt interface before removing without exceeding 400 degrees Fahrenheit.
*IE/ARP Crankshaft Damper Bolts are designed for use on late 06A 1.8T engine blocks only, they will not fit on early 058 engine blocks found in B5 A4 and B5 Passat models. 058 engine blocks are identified by having an external water pump and internal drive shaft.
2.0T FSI (EA113) 06F ENGINE
AUDI - A4 2005-2008 (B7) 2.0T FSI
AUDI - A6 2005-2011 (C6) 2.0T FSI
AUDI - A6 Allroad 2005-2011 (C6) 2.0T FSI
AUDI - TT 2008-2015 (MK2 - 8J) 2.0T FSI (TIMING BELT ENGINES ONLY)
AUDI - TTS 2008-2015 (MK2 - 8J) 2.0T FSI
AUDI - A3 2006-2013 (MK2 - 8P) 2.0T FSI (TIMING BELT ENGINES ONLY)
Step 1: Choose message placement
Click the button below and then hover over your page to select a placement.
Step 2: Paste and save
You have copied the placement for the Product Page.
Go back to the App Embeds section, and in the Paypal Advanced Settings, paste the copied value into the
Product Page field and click the 'Save' button in the top right corner.
| SKU:
ARP-06A-01
