ID1300-XDS Injectors Set of 10, 34mm Length, 14mm Grey Adaptor Top, 14mm Lower O-ring
Lamborghini Huracan/Audi R8 (V10)
In Stock:
This product is in stock & ready to be dispatched.
Limited Stock Available:
Stock is running low. Order soon to avoid missing out!
Almost Gone:
Stock is critically low! This product may sell out soon.
Incoming:
Product will be in stock soon.
Usually Ships In:
This product is out of stock and will usually ship in the timeframe displayed.
Sold Out:
This product is currently out of stock.
Request ETA
$3,809.95
Unit price /
Unavailable
Bidit helps you and Pro Speed Racing agree on a price. You set the price and Pro Speed Racing checks if they can accept your offer. You aren't competing with anyone else.
This store accepts price offers on this product through Bidit. AI agents can negotiate programmatically: when WebMCP is available this page registers the tools bidit_get_offer_context, bidit_make_offer and bidit_add_offer_to_cart. Documentation for the offer flow: /apps/bidit/agents on this store, or https://app.thebidit.com.au/agents.
Make us an offer and we'll try and make it work.
Price$3809.95
‹›
$
$0.00$3809.95
You have two offers on this product today.
You have two offers on this product today.
Crunching the numbers
Can you meet us higher?
$0.00
First offer
‹›
$
$0.00$3809.95
You have one offer remaining on this product today.
You have one offer remaining on this product today.
Ten Injector Dynamics ID1300-XDS injectors make up this set, each 34mm long with a 14mm grey adaptor top and a 14mm lower O-ring. It is a strong match for an engine running ten injectors that moves between ethanol blends and petrol, where alcohol resistance and clean low-speed running both count. Flex fuel, minus the fuss at idle.
Injector Dynamics is the manufacturer. Pro Speed Racing is its appointed Main Wholesale Distributor for the Australian and New Zealand market and carries the wider ID injector and parts catalogue, as well as plenty of other aftermarket car parts.
Fitment by part number
Part number: 1300.34.14.14.10
Quantity: 10 injectors
Length: 34mm
Top: 14mm grey adaptor
Lower: 14mm O-ring
Flow rating, pressure limit and connector are covered in the Technical Specifications section further down.
Designed around alternative fuels
The ID1300-XDS was an all-new design from the Injector Dynamics and Bosch Motorsport partnership, and at launch it was the only performance injector with fully stainless internals. Injector Dynamics says it works with every known fuel and stands up well to the corrosive nature of alcohol. Its minimum fuel mass also suits petrol, so idle and cruise stay well behaved if the engine goes back to pump fuel.
Ordering the right set
Compare the 34mm length and 14mm O-ring sizes with the injectors you are replacing, and look over the Vehicle Fitment tab before checking out. Planning for the next service? Injector Dynamics sells the 14mm brown Viton lower O-ring individually, so a single tired seal can be swapped on its own.
Technical Specifications
Nominal Flow Rate: 1335cc/min @ 3.0 Bar (43.5 psi) Using Iso Octane at 52 Degrees C (125 Degrees F)
Maximum Differential Fuel Pressure: 7.0 Bar (101.5 psi)
Fuel Compatibility: Compatible With All Known Fuels – (Designed Specifically for Alternative Fuels)
Step 1: Choose message placement
Click the button below and then hover over your page to select a placement.
Step 2: Paste and save
You have copied the placement for the Product Page.
Go back to the App Embeds section, and in the Paypal Advanced Settings, paste the copied value into the
Product Page field and click the 'Save' button in the top right corner.